Samsung N7100 Root File 4.4.2 Download ((link)) Jun 2026

Rooting Your Samsung Galaxy Note 2 (N7100) on Android 4.4.2 KitKat The Samsung Galaxy Note 2 (GT-N7100) remains a legendary device in the Android community. While Android 4.4.2 KitKat was its final official major update, rooting the device opens up a world of possibilities, from removing bloatware to installing custom ROMs like LineageOS. If you are looking to download the root files and get started, this guide will walk you through the process using the most reliable method: CF-Auto-Root . Prerequisites Before You Begin Rooting carries risks, including voiding your warranty and potential data loss. Ensure you have completed the following: Backup Your Data: Back up your photos, contacts, and messages. Battery Level: Ensure your phone has at least 60% charge. USB Drivers: Install the Samsung USB Drivers on your PC. Enable USB Debugging: Go to Settings > About Device . Tap Build Number 7 times until "Developer Mode" is enabled. Go to Settings > Developer Options and toggle on USB Debugging . Download Section: Required Files To root the N7100 on 4.4.2, you need a specific package. Download these to your PC: CF-Auto-Root Package for GT-N7100: [Download Link] (Search for CF-Auto-Root-t03g-t03gxx-gtn7100.zip ) Odin3 Flashing Tool: (Usually included in the CF-Auto-Root zip file). Step-by-Step Rooting Guide Step 1: Prepare the Files Extract the CF-Auto-Root-t03g-t03gxx-gtn7100.zip file on your desktop. You should see a .tar.md5 file and the Odin3.exe application. Step 2: Enter Download Mode Power off your Note 2 completely. Press and hold Volume Down + Home + Power buttons simultaneously. When a warning screen appears, press Volume Up to enter Download Mode. Step 3: Connect to PC Launch Odin3 as an Administrator. Connect your Note 2 to the PC using a high-quality USB cable. The "ID:COM" box in Odin should turn blue or yellow, indicating the device is recognized. Step 4: Load the Root File In Odin, click the AP (or PDA in older versions) button. Select the CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5 file you extracted earlier. Ensure only "Auto Reboot" and "F. Reset Time" are checked in the Options tab. Do not check "Re-Partition." Step 5: Start the Flash Click the Start button. The process usually takes less than a minute. Your phone will reboot automatically. Once you see a green PASS! message in Odin, you can safely disconnect your device. Verifying Root Access Once the phone reboots, look for the SuperSU app in your app drawer. To be 100% sure, download Root Checker from the Play Store. Run the app and tap "Verify Root." If you see a "Congratulations!" message, you are officially a superuser. Troubleshooting Stuck on Boot Logo: If the device loops, boot into Recovery Mode (Volume Up + Home + Power) and perform a "Wipe Cache Partition." Odin Doesn't Recognize Phone: Try a different USB port or reinstall the Samsung drivers. Disclaimer: Rooting is done at your own risk. This guide is for the GT-N7100 model only. Attempting this on other variants may brick the device.

Samsung N7100 (Galaxy Note II) — Root guide for Android 4.4.2 (KitKat) Warning: rooting can void warranty, may brick your device, and can cause data loss. Back up important data before proceeding. Proceed only if you understand and accept those risks. Overview This guide describes how to root the Samsung Galaxy Note II (model N7100) running Android 4.4.2 (KitKat). It covers preparing your device, required files and tools, step-by-step rooting using Odin and a compatible CF-Auto-Root or custom recovery, and post-root checks. Requirements

Samsung Galaxy Note II (N7100) with Android 4.4.2 installed. Windows PC with Odin (v3.09 or compatible). Samsung USB drivers installed on the PC. USB cable (original or good-quality). Battery charged to ≥60%. Backup of your data. Known ODIN-compatible CF-Auto-Root package or compatible custom recovery (TWRP) and a SuperSU or Magisk ZIP (for post-root management).

Files (what to download)

Samsung USB Drivers for Windows. Odin flashing tool (v3.09 recommended). CF-Auto-Root package specifically built for N7100 and Android 4.4.2 (ensure model and Android build match).

Alternative: TWRP recovery image for N7100 + Magisk ZIP or SuperSU ZIP.

Optional: Stock firmware for your exact N7100 variant (for recovery in case of bad flash). samsung n7100 root file 4.4.2 download

Important: Only use files that explicitly list N7100 and Android 4.4.2 / KitKat compatibility. Using mismatched files (different model or carrier variant) can brick the device. Preparation

Install Samsung USB drivers on the PC. Enable Developer options on the phone: Settings → About device → tap Build number 7 times. In Developer options enable USB debugging. Disable Kies and any PC-side Samsung software that may interfere. Put the phone into Download Mode: power off → press and hold Volume Down + Home + Power → confirm with Volume Up.

Rooting via CF-Auto-Root (Odin) This is the standard, simple method if a CF-Auto-Root package exists for your exact build. Rooting Your Samsung Galaxy Note 2 (N7100) on Android 4

Extract Odin ZIP on your PC and run Odin3.exe as Administrator. Extract the CF-Auto-Root ZIP to get a .tar.md5 (or .tar) file. In Odin, click the AP (or PDA) button and select the CF-Auto-Root .tar(.md5) file. Connect the phone in Download Mode via USB. Odin should show an “Added!” message and a blue COM port. Ensure only “Auto Reboot” and “F. Reset Time” are checked. DO NOT check “Re-partition”. Click Start. Odin will flash the package; wait until it shows “PASS” (green). Phone will reboot and the first boot after rooting may take several minutes. After boot, install a root checker app or verify that the SuperSU/Magisk app is present and that root access can be granted.

Rooting via TWRP + Magisk (recommended if CF-Auto-Root not available)